Preset, Patrol, Pattern, Recording, upload FTP, email linkage
1 Mic in/Line in interface
Line input: 2-2.4V[p-p]; output impedance: 1KΩ, ±10%
1 Audio output interface
Pan and Tilt
8 groups, each group for 16 presets
4 groups, each group record 3 mins
H.264 Main Profile encoding ;
MJPEG / JPEG Baseline encoding
1280 * 960 , 25fps
704*576, 640*480, 352*288, 320*240, 25fps
Video bit rate
32Kbps-16Mbps continuously adjustable, support CBR / VBR
50HZ:25fps(1280×960) 60HZ：30fps (1280×960)
If you are interested in our p2p night vision cmos sensor infrared wifi cctv 4x bullet camera, welcome to buy our famous brands' products. As one of the most professional security products manufacturers and suppliers, we will offer you high-quality and newest product with CE certififacation as well as the best service. For more info, contact our factory now.
Mini PTZ Bullet Camera
IP PTZ bullet camera User Manual
All IP PTZ bullet camera Series
Analog PTZ bullet camera User Manual
All analog PTZ bullet camera Series
Thank you for buying our company product, any question or request please feel free to contact us.
The manual only use for our IP PTZ bullet camera.
This manual maybe includes some inaccurate information on technology/product function/ operation or print error, we will update it in the new versions manual in future.
Please read this manual carefully before you install and operate the IP PTZ bullet camera.
● Transportation Security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage. Every unit should be transported in separated packing. In shipments of distributor and delivery of maintenance, any damages caused by integral packing are not covered by warranty.
● Installation Security
It has 2 installation ways: wall mounting and ceiling mounting, avoid mixing installation!
The dome camera must be handle with care! Avoid heavy stress and violent vibration during installation. Don't touch the dome cover directly by hand. When connecting the power source, please follow all electric safety standards and only use the power supply designed for this device. Keep the video and control signal in a decent distance with high voltage devices and cable. Don't apply power to dome before finishing the installation.
● Don't remove
Internal removing, assembly, repair and operations should be only performed by our company or qualified service personnel.
The video image would be interfered when the dome is installed from Television, radio transmitter, voltage changer and audio amplifier.
Avoid shooting very bright objects directly into the camera (such as the sun or light fittings) and avoid fixating the camera lens on bright static object for long time, as it will cause Irreparable damage to the camera.
Avoid heavy stress and violent vibration! Please don't use abrasive and violent detergent to clean the dome. Please choose dry fabric and neutral detergent. And please use lens paper to clean the lens.
●Please use our product according the work environmental standards.
IP Mini PTZ Bullet Camera. - 3 -
Ⅰ.Computer IE Web Browser. - 3 -
Ⅱ.Key Button Explanation. - 3 -
III.Preset Setup. - 4 -
IV.Scan Settings. - 5 -
VI.Instruction List - 5 -
Analog Mini PTZ Bullet Camera. - 7 -
I. Cable Definition. - 7 -
II. Address, Protocol, Baud Rate Setting. - 7 -
IV.PTZ camera instruction list - 7 -
After-Sales Service. - 8 -
Ⅰ.Computer IE Web Browser
1.IP PTZ bullet camera connect with the local area network(LAN) or connect with computer directly, make sure the network segment of computer IP is "1", open the computer IE browser, input default IP: 192.168.1.160, as below picture:
2.Input the default User Name: admin, Password:12345, click "log in" enter into camera's control interface, as below picture:
Ⅱ.Key Button Explanation
Control the horizontal and vertical movement of the camera ,and open/close automatic scan
Speed adjustment of PTZ
open/close Lamp light
main/sub code stream change
3D function switch
1.Preset setup, call, delete
As image 11, turn the PTZ cam to the position where you need, and click to setup, click to call, click to delete
2.Cruise setup ,call, delete
Click can choose 8 cruise;
Clickadd the preset which you need, and setup the cruise time and speed, each cruise support max 16 presets as below
After adding required preset, please click to save the cruise, Click to call this cruise, click to stop the cruise,Click to delete the preset in the cruise, click can edit the preset in the cruise, after deleting and editing, click to save.
Support A, B two points auto scan, random scan, pattern scan
Clickto call random scan, click again to stop;
2.A,B two dots automatic scan
Rotate the dome camera to the needed position, click to set up the left limited position of scan;Rotate the dome camera to the needed position, click to set up the right limited position of scan;Then click thus can start the scan of the set up area between A,B two dots; click it again to stop scanning
Calling the Menu of the camera module
Setup/Calling preset 45
Setup left limit
Setup/Calling preset 46
Setup left limit
Setup right limit
Setup/Calling preset 47
|Setup right limit|
A to B scanning
Setup/Calling preset 48
|A to B scanning|
Setup/Calling preset 49
Default scanning speed is 1
Pan& Tilt speed 1
Setup/Calling preset 50
Setup Pan& Tilt speed
Pan& Tilt speed 2
|Setup/Calling preset 51|
Pan& Tilt speed 3
|Setup/Calling preset 52|
Pan& Tilt speed 4
|Setup/Calling preset 53|
Pan& Tilt speed 5
|Setup/Calling preset 54|
Scanning speed 1
Setup/Calling preset 60
Setup Scanning speed
Scanning speed 2
|Setup/Calling preset 61|
Scanning speed 3
|Setup/Calling preset 62|
Scanning speed 4
|Setup/Calling preset 63|
Scanning speed 5
|Setup/Calling preset 64|
1.Stop recording track：If the presets can't be deleted，you can stop record by calling the track；
Signal, power supply cable connection, please reference following chart:
Decoder of PTZ will automatically match protocol,no need to set; support PELCO-D,PELCO-P.Factory default PTZ address is code 1 and baud rate is 2400. If you want to modify them, follow the following steps:
First method(for models with NO OSD menu):
Call No.101—No.199 to set the address is 1—99.Call No.201—No.204 to set the baud rate is 1200,2400,4800,9600.If you forget the adress,you can use the Universal address code 255 to control the PTZ,and then you can call the corresponding preset to set the address and baud rate what you want. Please restart the camera after you modified.
Second method(for models with OSD menu):
Except for method 1,Please call No.95 preset to enter Main Menu, system setup and Com setup, after that, you can modify them. Please restart the camera after you modified.
5.camera menu setup
3.motion speed: 02
2.Com Addr: 01
Mode Of Operation
Call 101—199,the address is 1—99
Baud Rate Setting
Call 201,202,203,204,the baud rate is 1200,2400,4800,9600
Address code 255
The first cruise line（1-16 presets）
The second cruise line（17-32 presets）
The third cruise line（33-48 presets）
The fourth cruise line（240-255 presets）
A cruise preset for 4 seconds
A cruise preset for 8 seconds
A cruise preset for 10 seconds
A cruise preset for 15 seconds
A cruise preset for 20 seconds
Set the left limit point A
Set the right limit point B
To enable A, B two points scans
To clear A, B two points scans
Call 65, 66, 67, 68, 69 preset position, the corresponding rate is 3, 6 degrees per second, 9, 15 degrees and 40 degrees
Idle task setting
Call 61:Preset level 1
|Call 63:A/B scans|
|Call 64: Horizontal scan|
clear all of the presets
Open the camera menu
Open the dome menu
Restore the factory
NOTE: If the camera without OSD menu, you must NOT to call 95 preset, it will lead to the camera out of control;If do this by mistake, you need power off to restart, or you can no need do any operate until 1 minute,the camera can be return to normal and can control it.
Dear user, in order to get the high quality service for the IP PTZ bullet camera, please read the below service charters.
1. We can offer the service of limited warranty and life-long maintenance
(1)In the limited warranty (within 12 month from getting the camera), you can enjoy the maintenance free service. Note: improper operation, man-made fault and other irresistible reasons are excluding of the limited warranty.
(2) If beyond 12 months from you getting the camera, our company promises that we will provide a payment that if customer needs maintenance service for life.
2. Repair response time
(1) When the camera arrives at our company, the response service is within 24 hours.
(2) The customer need contact our company staff before sending camera back; if not, customer will be responsible for the risk of untimely repair.
In the warranty period, our company offer free repair; but it will pay for the material cost when include any of below situation:
(1) It is damaged due to not follow the manual to operate.
(2) It is damaged due to lightning, fire disaster and other force majeure factors.
(3) It is damaged due to matching with other poor design products, which produced by other manufacturer.
Because of continuous new technology, so there is no further notice for change of specifications.
Company has the authority to ultimate interpretation for the manual.